FINGERPRINT SENSOR ZFM-708

Specifications

power: DC 3.8 V to 7.0 V
back light: green
baud rate: (9600 x N)bps, N=1-12 (default N=6)
image acquiring time: <0.5 s
finger prints storage capacity: 1000
false acceptance rate: 0.001% (at security level 3)
false reject rate: 1.0% (security level 3)
interface: TTL serial
operating current (max.): 95 mA
average searching time: 1 s
working temperature: -20 - +50 °C
outline dimensions: 54 x 20 x 20.5 mm

IR OBSTACLE AVOIDANCE SENSOR MODULE

This module is an inexpensive solution for an obstacle avoidance sensor, perfect for robotic projects and very easy to interface directly with Arduino and compatible boards. The module has two potentiometers, one to control frequency and one to control the intensity.
Specifications

operating voltage: 3.3 V to 5 V
output: digital (on/off)
detection threshold: adjustable by 2 trimmers
distance range: 2 to 10 cm
adjustment R6: frequency adjustment 38 KHz (already optimised)
adjustment R5: IR LED power adjustment (already optimised)
operating temperature: -10°C to +50°C
effective angle: 35°
I/O interface: 4 wire interface (- / + / S / EN )
dimensions: 45 x 16 x 10 mm
weight: 9 g

1 CHANNEL LATCHING RELAY MODULE WITH TOUCH BISTABLE SWITCH 12 V

Specifications

supply voltage: 12 VDC
supply current: 15 - 50 mA
trigger current: 0.5 mA
contact rating: 10 A 250 VAC / 10 A 30 VDC
dimensions: 5 x 2.5 x 2 cm
weight: 25 g

1 CHANNEL SOLID STATE RELAY MODULE

Specifications

power supply: 5 VDC
power current: max. 10 mA
input voltage:
relay OFF: 0 to 2.5 VDC
relay ON: 3.3 to 5 VDC
max. load: 240 VAC 2 A 50/60 Hz
dimensions: 2.5 x 2.5 x 3.6 cm
weight: 6 g
protection: 2A Pico fuse on board

TB6560 3A STEPPER MOTOR DRIVER BOARD

Features

6N137 high-speed OptoCouple to ensure high speed without losing steps
for 42,57,86 Stepper within 3A 2/4 -phase / 4 wire / 6 wire stepper motor
automatic half-decay
excitation mode: synchronizing, half step, 1/8 step, 1/16 step
current level is adjustable to meet your application needs
large heat sink for good heat dissipation
overheating and over-current protection circuit to ensure optimal performance

Specifications

operating voltage: 10 to 35 VDC
rated output current: ± 3 A - peak 3.5 A
dimensions: 50 x 75 x 35 mm
weight: 80 g

FORCE-SENSING RESISTOR (FSR)

This FSR (Force Sensing Resistor) will vary its resistance depending on how much pressure is being applied to the sensing area. A 2.54 mm male pinheader is provided making it easy to use on bread boards.

Specifications
sensor type: single point
shape of sensitive area: round
diameter of sensitive area: 10 mm (+/- 1 mm )
total lenght: 39 mm
sensor thickness: 0.2 mm
material: polyester
range: 100 g to 1 kg
terminal: male pinheader step 2.54 mm
principle: piezoresistive
service life: > 500.000 times
operating temperature: -25°C to 90°C

BME280 TEMPERATURE, HUMIDITY AND PRESSURE SENSOR

The BME280 used on this combo module is an integrated environmental sensor developed specifically for mobile applications where size and low power consumption are key design constraints.

The BME280 supports both SPI and I2C interface to communicate with the microcontroller.

Features
applications:
measurement of volume and air flow
home automation control
control heating, ventilation, air conditioning
internet of things
weather forecast
fitness monitoring / well-being
Specifications
pressure range: 300 to 1100 hPa
temperature range: -40 to 85°C
supply voltage: 1.2 to 3.6 V
I/O voltage: max 3.6 V
current consumption: max. 3.6 uA @ 1 Hz (H,P,T)
sleep mode consumption: 0.1 uA
interface: I2C and SPI
dimensions: 15 x 12 mm

VL53L0X TIME-OF-FLIGHT RANGING AND GESTURE DETECTION SENSOR

The VMA337 is a breakout board for STs VL53L0X laser-ranging sensor and measures the range to a target object up to 2 m away.

Specifications
power supply: 3.3 - 5 VDC
infrared emitter: 940 nm
range: 30 to 2000 mm
ranging accuracy: +/- 3 %
sampling time: <= 30 ms
operating temperature: -20 to 70 °C
interface type : I2C
supply current: 10 mA
XSHUT and GDPIO voltage: max 2.8 V

HM-10 WIRELESS SHIELD FOR ARDUINO UNO

The VMA338 uses a HM-10 module with Texas Instruments CC2541 Bluetooth v4.0 BLE chip, fully compatible with VMA100 UNO. This shield has extended all the digital and analog pins out into 3PIN, making it easy to connect to sensors using 3PIN wire.

Features
extends 14 digital pins to 3pin
extends 6 analog pins to 3pin
on-board reset button
comes with a slide switch to power wireless communication on or off
jumper interface to control serial communication
integrated Texas Instruments CC2541 Bluetooth v4.0 chip on board
Specifications
pin header spacing: 2.54 mm
Bluetooth chip: Texas Instruments CC2541
USB protocol: USB V2.0
working frequency: 2.4 GHz ISM band
modulation method: GFSK (Gaussian Frequency Shift Keying)
transmission power: -23 dbm, -6 dbm, 0 dbm, 6 dbm, can be modified by AT command
sensitivity: =-84 dBm at 0.1% BER
transmission rate: asynchronous 6K bytes
security: authentication and encryption
supporting service: central & peripheral UUID FFE0, FFE1
power consumption: 400-800 uA during standby, 8.5 mA during transmission
power supply shield: 5 VDC
power supply HM10: 3.3 VDC
working temperature: -5 to +65 °C
dimensions: 54 x 48 x 23 mm
weight: 19 g

PULSE / HEART RATE SENSOR MODULE FOR ARDUINO

VMA340 is a plug-and-play heart rate sensor for Arduino and Arduino compatibles. It can be used by anyone who want to incorporate live heart rate data into their projects.

Features
WARNING: NOT FOR MEDICAL USE
VMA340 is not intended to diagnose, prevent or treat any condition, or to be a substitute for professional medical care. Measurements and statistics are intended for informational and educational purposes only. VMA340 is not compliant with the European Council directive 93/42/EEC concerning medical devices and is not approved by the U.S. Food and Drug Administration. If knowing your pulse rate is critical to your health, you need to have your pulse taken by a medical professional.
Specifications
diameter: 16 mm
overall thickness: 3 mm
working voltage: 3 to 5 V
working current: 4 mA at 5 V
cable length: 18 cm
connections: GND, VCC, analog signal out

BH1750 DIGITAL LIGHT INTENSITY SENSOR MODULE

VMA341 (BH1750) is a digital ambient light sensor for I2C bus interface. This module is the most suitable to obtain ambient light data for adjusting LCD and the keypad backlight power of mobile phones.

Features
I2C bus interface
spectral responsibility is approximately human eye response
illuminance to digital converter
wide range and high resolution. ( 1 - 65535 lx )
low current by power down function
module contains 5V to 3.3V converter
50 Hz / 60 Hz light noise reject function
no need for any external parts
adjustable measurement result for influence of optical window (this function allows to detect min. 0.11 lx, max. 100000 lx)
small measurement variation
very small influence of infrared
Specifications
supply voltage: 5 V
voltage: 3.3 VCC
operating temperature : -40°C - +85°C
SDA sink current: 7 mA
power dissipation: 260 mW
dimensions : 20 x 30 mm

A/D D/A CONVERTER MODULE PCF8591

The VMA344 - PCF8591 is a monolithically integrated, low-power, 8-bit CMOS data acquisition device. The PCF8591 has four analog inputs, one analog output and a serial I2C bus interface.
For testing purposes, the VMA344 contains a phototransistor, NTC and a trimmer which are connected to the PCF8591 by 3 jumpers.

Features
single power supply
operating supply voltage 2.5 V to 6.0 V
low standby current
serial input and output via I2C-bus
max sampling rate given by I2C-bus speed
4 analog inputs configurable as single ended or differential inputs
auto-incremented channel selection
analog voltage range from VSS to VDD
on-chip track and hold circuit
8-bit successive approximation A/D conversion
multiplying DAC with one analog output

4 CHANNEL RELAY MODULE

This 4-channel relay interface board can control various appliances and other equipments with high current. It can be controlled directly by any micro-controller.
Features

standard interface that can be controlled directly by any microcontroller
opto-isolated inputs
indicator LEDs for relay output status

Specifications

control input current (in1 to in4): 5 - 15 mA
control input voltage: 5 - 12 VDC
relay output: 250 VAC 10 A, 30 VDC 10 A (non-inductive)

5 VDC STEPPER MOTOR WITH ULN2003 DRIVER BOARD

A small and versatile motor and driver set. This 5 VDC stepper motor controlled by the ULN2003 driver can be used with any Arduino or compatible boards via jumper leads. Four-phase LED indicates the status of the stepper motor.
Features

with LED step indicators
included: 5 V stepper motor
ULN2003 controller module
cable

Specifications

operating voltage: 5 VDC
steps / revolution: 64
controller: ULN2003
motor diameter: 28 mm
reduction ratio: 1:64
number of phases: 4
dimensions: 35 x 32 x 10 mm

LM2577 DC-DC VOLTAGE STEP-UP (BOOST) MODULE

This module converts the microcontrollers power supply into a higher, adjustable voltage.
Specifications

input voltage: 3.5 to 35 VDC
output voltage: 5 to 55 VDC (adjustable)
max. input current: 3 A
continuous input current: 2 A
chip: LM2577
dimensions: 43 x 30 x 12 mm

DC-DC BOOST MODULE / (2.5 V-5 V) 600 mA TO USB 5 V (2 pcs)

This module provides a stable 5 V from a single Li-Po or two alkaline cells.
Specifications

input voltage range: 2.5 to 5 VDC
output voltage: 5 VDC
connection: solder pads
dimensions: 34 x 16 x 8 mm

DC-DC ADJUSTABLE VOLTAGE STEP DOWN MODULE LM2596S

Specifications

input voltage: 3 to 40 VDC
output voltage: 1.25 to 35 VDC
max. output current: 2.5 A
chip: LM2596S
dimensions: 49 x 26 x 12 mm

ARDUINO COMPATIBLE RFID READ AND WRITE MODULE

This RFID module allows to both read and write MiFare-type RFID cards.
Specifications

operating voltage: 3.3 VDC
working current: 13 to 26 mA
sleep current: < 80 uA
peak current: < 30 mA
working frequency: 13.56 MHz
supported card types: Mifare cards
interface / protocol: SPI
controller chip: MFRC522
data transmission speed: Max. 10 Mbit / s
dimensions: 66 x 40 x 7 mm
includes: 2 tags (1 card , 1 fob)

ARDUINO COMPATIBLE 5 V RELAY MODULE

Specifications

operating voltage: 5 VDC
relay current rating: 10 A at 250 VAC, 10 A at 30 VDC (non inductive)
relay contact: C, NO, NC
connection : GND, +5 VDC, control input (5 to 12 VDC)
dimensions: 40 x 27 x 18 mm

PHOTOSENSITIVE SENSOR MODULE WITH 3 PIN CABLE

Measure light levels with this sensor module!
This module uses a photo transistor to produce an output voltage that will vary at different light levels. Connect it to your Arduino or any other development board to build a night/day sensor, a sun tracker or combine it with a laser module to make a laser trip wire.

Specifications
operating voltage: 3.3 VDC to 5 VDC
output: analog voltage
pull-down resistor: 10 K (on-board)
dimensions: 25 x 15 mm